In-System SPI Flash Programmer

Filter
–
27.1 %

Product Nr.: SF700
The SF700 is a high-speed ISP programmer for updating the on-board soldered SPI flash.
...show more
Hardware Features
- Built-in high speed processor for high programming speed.
- Supports SPI Octal NOR Flash, SPI NOR Flash, and SPI NAND Flash.
- Supports a variety of file formats such as Binary, Intel Hex, Motorola S19 and ROM, etc.
- Supports command line mode for new software development.
- Supports stand-alone mode for IC programming without PC.
- ATE port with ISP adapter, provides Busy/Pass/Error and Start pins for remote control.
- Supports 1.2V low voltage IC.
- Multiple programmers support parallel programming of IC.
Software Features
- PC based SF700 programming software with different modes:
- Engineering Mode features advanced developer and repair functions
- Production mode for simultaneous control of multiple SF700 programmers
- Command line to control the SF700 by user defined software
- Supports Windows 2003 (32 bit and 64 bit) and higher
Applications
- Updating of the serial flash soldered to the board with or without power supply in standalone or PC GUI mode
- Prototype or low volume production, in-system or socket programming
- Control application, controller reset and MOSFET isolation status
- Update of internal flash (Ezport MCF5223, MCF5221, MCF5213) or external SPI flash (SBF interface MCF5445, MCF5227) of Freescale MCU
Product is discontinued

Product Nr.: TP240141
TP240141 - The Aardvark I2C/SPI Host Adapter is a fast and powerful I2C bus and SPI bus host adapter through USB.
...show more
I2C Features
- Performance of up to 800 kbps over USB with higher bandwidth compared to slower RS-232.
- Supports standard mode (100 kbps) and fast mode (400 kbps) and varying speeds from 1 kHz to 800 kHz.
- Supports inter-bit and inter-byte clock stretching, multi-master configurations, master send and receive, and asynchronous slave send and receive.
- Software configurable I2C pull-up resistors.
- Software-configurable target power pins to power downstream devices.
- Repeated start, 10-bit slave addressing, and combined format transactions.
- Display Data Channel (DDC)
- System Management Bus (SMBus)
- Power Management Bus (PMBus)
- Smart Battery Bus (SBBus)
- Intelligent Platform Management Interface (IPMI)
- Two Wire Interface (TWI)
† Actual system bus speed may vary based on capacity.
SPI Features
- Works in master or slave mode.
- Master signaling rate of up to 8 Mbit/s.
- Slave signaling rate of up to 4 Mbit/s.
- Send/receive full-duplex master.
- Asynchronous slave send / receive.
- Software-configurable target power pins to power downstream devices.
- Software-configurable slave select (SS) polarity in master mode.
€339.00*

Product Nr.: TP280121
The Cheetah SPI Host Adapter is a high-speed SPI adapter that is capable of communicating over SPI at up to 40+ MHz.
...show more
SPI Features
- Works in master or slave mode.
- Master signaling rate of up to 8 Mbit / s.
- Slave signaling rate of up to 4 Mbit/s.
- Send/receive full-duplex master.
- Asynchronous slave send / receive.
- Software-configurable target power pins to power downstream devices.
- Software-configurable slave select (SS) polarity in master mode.
€419.00*

Product Nr.: TP500110
Promira is a universal hardware platform usable for a variety of applications, like I2C, SPI and eSPI.
...show more
I2C Features
- Performance of up to 800 kbps over USB with higher bandwidth compared to slower RS-232.
- Supports standard mode (100 kbps) and fast mode (400 kbps) and varying speeds from 1 kHz to 800 kHz.
- Supports inter-bit and inter-byte clock stretching, multi-master configurations, master send and receive, and asynchronous slave send and receive.
- Software configurable I2C pull-up resistors.
- Software-configurable target power pins to power downstream devices.
- Repeated start, 10-bit slave addressing, and combined format transactions.
SPI Features
- Works in master or slave mode.
- Master signaling rate of up to 8 Mbit/s.
- Slave signaling rate of up to 4 Mbit/s.
- Send/receive full-duplex master.
- Asynchronous slave send / receive.
- Software-configurable target power pins to power downstream devices.
- Software-configurable slave select (SS) polarity in master mode.
€900.00*

Product Nr.: SF100
The SF100 is a high speed ISP programmer for updating the on-board soldered SPI flash.
...show more
Hardware Features
- SPI Flash In System Programming
- SPI Flash Socket Programming (SF100 Bottom Board required)
- Power supply of the target IC
- Manual start button to initiate programming
- USB control via PC
- Support of 1 CS pin
- Built-in signal conflict protection
Software Features
- PC based SF100 programming software with different modes:
- Engineering Mode features advanced developer and repair functions
- Production mode for simultaneous control of multiple SF100 programmers
- Command line to control the SF100 by user-defined software
- Supports Windows 2003 (32 bit and 64 bit) and higher
Applications
- Updating of the serial flash soldered to the board with or without power supply
- Prototyping or low volume production, for socket programming the bottom board is required
- Control application, controller reset and MOSFET isolation status
- Update of the internal flash (Ezport MCF5223, MCF5221, MCF5213) or the external SPI flash (SBF interface MCF5445, MCF5227) of the Freescale MCU
€270.00*

Product Nr.: SF600Plus
The SF600 Plus is a high-speed ISP programmer for updating the on-board soldered SPI flash.
...show more
Hardware Features
- USB High Speed and high SPI performance, allows programming up to 2Gb SPI Flash.
- In-circuit programming: programming SPI Flash on the board
- Off-line programming: programming SPI Flash in the socket
- Start button function: Batch operation possible in USB mode
- Standalone mode: Supports start button programming and IO port programming.
- ISP port supports 2 CS pins for programming two Serial Flash memories
- Signal conflict protection
- Multi-programming capability via USB
- Supports 1.8V low voltage IC
- Supports Windows 2003 and above
- Supports both 32 and 64 bit operating systemsSoftware Features
- PC based SF600 Plus programming software with different modes:
- Engineering Mode features advanced developer and repair functions
- Production mode for simultaneous control of multiple SF600 Plus programmers
- Command line for controlling the SF600 Plus through user-defined software
- Supports Windows 2003 (32 bit and 64 bit) and higher
Applications
- Updating of the serial flash soldered to the board with or without power supply in standalone or PC GUI mode
- Prototype or low volume production, in-system or socket programming
- Control application, controller reset and MOSFET isolation status
- Update of internal flash (Ezport MCF5223, MCF5221, MCF5213) or external SPI flash (SBF interface MCF5445, MCF5227) of Freescale MCU
Product is discontinued

Product Nr.: SF600Plus-G2
The Dediprog SF600Plus-G2 is a high-speed serial NOR/NAND flash programmer with in-circuit programming.
...show more
Hardware Features
- High-speed USB and high SPI performance; the USB and standalone mode support any volume of SPI flash on the market.
- Supports 1.2V low voltage IC.
- Start button function: can batch when connected to the software.
- Protection against signal conflict.
- Multi-programmer capability via USB.
- Programmer index indicators on the programmer.
- Supports 2 CS pins.
- Stand-alone mode: support start button programming and control port to remove control programming.
- Supports WIN8 and above.
- Supports both 32bit and 64bit OS.
- Supports Single/Dual Multiple Dies.
- Supports Single/Dual/Quad/Octal. IO.
- Can be upgraded to SF600Plus-G2U.
Software Features
- PC based SF600-G2 programming software with different modes:
- Engineering Mode features advanced developer and repair functions
- Production mode for simultaneous control of multiple SF600-G2 programmers
- Command line for control of the SF600-G2 by user-defined software
- Supports Windows 2003 (32 bit and 64 bit) and higher
Applications
- Updating of the serial flash soldered to the board with or without power supply in standalone or PC GUI mode
- Prototype or low volume production, in-system or socket programming
- Control application, controller reset and MOSFET isolation status
- Update of internal flash (Ezport MCF5223, MCF5221, MCF5213) or external SPI flash (SBF interface MCF5445, MCF5227) of Freescale MCU
€380.00*

Product Nr.: SFDK01-G2
The SPI Flash Development Kit offers engineers a complete solution for developing firmware based on SPI Flash memory.
Produkt abgekündigt

Product Nr.: SFDK03-G2
This kit combines all the accessories of the EM100Pro-G2 and the SF600Plus and offers the user greater price advantages than purchasing them individually.
Produkt abgekündigt

Product Nr.: SuperPro IS01
The Xeltek Superpro IS01 is a multifunction serial programmer with high programming speed.
...show more
Functions
- Supports all major ISP protocols (e.g. I2C, SPI, UART, BDM, MW, JTAG, CAN, RS232). Contact Xeltek for more details
- Offers VDD (0.5A) output line and VPP (0.2A)
- Operating temperature 10-50°C
- ESD protection - I/O level is set via SuperProIS01 software (1.5V ~ 4V)
- Online software runs the programmer and manages offline projects via USB2.0
- When working offline, the processes are displayed on the integrated LCD screen, the keyboard and the LED status indicator.
- Project files can be saved using a removable SD card (max. 4GB)
- The ATE interface allows the programmer to be operated and controlled by external signals. There are six project select lines (SEL0 - SEL5), two command input lines (START and STOP) and three
- Status output lines (PASS, FAIL and BUSY). External signals are isolated from the system via optocouplers
- 12V DC / 2A external system power supply
- High programming speed selectable: adjustment to cable length and loading function for target plate.
- Support online (USB2.0 High-Speed) and offline mode simultaneously.
- Supports all major ISP protocols (e.g. I2C, SPI, UART, BDM, MW, JTAG, CAN, RS232).
- Includes for automated operation.
- Built-in overcurrent protection function.
- Field-proven for R&D, mass production and custom in-system programming projects.
- The programmer works in either PC-hosted mode or standalone mode.
- In PC hosted mode, a PC controls the programmer over a high-speed USB2.0 connection for device programming.
- In standalone mode, the user controls the programmer via a built-in LCD screen and keyboard.
- An SD card stores project files.
- Compatible with Windows XP / Vista / 7 / 8 / 10 (32/64 bit)
€919.00*

Product Nr.: SuperPro IS416
The Superpro IS416 is a general purpose in-system gang programmer that can program up to 16 ICs at a time.
...show more
Functions
- High speed, industrial grade ISP production programmer. The ultimate choice for ISP subsystem integration.
- Supports almost all serial chips including but not limited to SPI, I2C, JTAG, BDM, UART, MON, SCI, SWD, SBW, C2D, ICC, SWIM, SDQ, DBG, ICE , CSI, LIN
- Supported manufacturers include but are not limited to ABOV, Ali, Altera, Atmel, Catalyst, Cypress, Freescale, Fujitsu, Haier, Hitachi, Hynix, Infineon, IR, ISSI, Lattice, Macronix, Maxim, Microchip, Micron, NEC, Numonyx, NXP, ON, Panasonic, Renesas, Rohm, Samsung, Sanyo, Silicon, Labs, Spansion, SST, ST, Teridian, TI, Toshiba, Winbond, Xilinx, Zilog
- Programs up to 16 serial chips or 4 parallel NAND, NOR, eMMC chips simultaneously
- Supports serial ISP programming for multiple chips of different models or types in one unit
- Common control ports provide signal isolation, relay isolation, power control, click detection, LED expansion indicator and other control signals
- Adjustable speed high-speed programming meets the requirements of board load or ISP cable length
- Three modes: 1) Online mode. Connected to local PC via USB2.0 (high speed) 2) Offline mode. With its dedicated keyboard, LCD display and mobile storage (standard SD cards), SuperPro IS416 can operate independently offline for flexible production and field setup. The size of the project file is only limited by the storage size of the SD card.3) Network mode. Connected to local network, control locally or remotely.
- Advanced pin driver technology delivers cleaner signals, wider voltage range and more accurate / higher clock frequency. Precise timing generators ensure higher speed and qualified product ratio for 1.2V-5.0V Vcc devices
- Chip Safety Mechanism: The built-in precise voltage self-calibration circuit ensures that the voltage is within the preset range at all times. The self-diagnostic function continuously detects hardware errors to ensure the machine runs normally.
- Overcurrent, overvoltage and ESD protection prevents damage to programmers
- The user operation interface is indicated by PCBA
- Log document and production statistics function make quality tracking easier.
- Copyright protection with SD encryption, document rights management and encryption, output limitation and remote control.
- Customized special functions and algorithm software available
- Web programmer + network management software (optional) create a revolutionary management mode for writing networks. Project setting, task switching and software update for all programmers can be completed instantly on one server, while quality monitoring and QC statistics can be performed in real time. Such errors as blank writing can be tracked and the written data is only stored on local or remote servers for data security reasons.
- With a custom socket adapter, SuperPro IS416 can be used as an offline production programmer, programming up to 4 chips at a time.
- Supports all major ISP protocols (e.g. I2C, SPI, UART, BDM, MW, JTAG, CAN, RS232)
- PC interface: USB2.0 (high speed), LAN (100M)
- Offline storage medium: SD card
- Keyboard and display: 6-key keyboard, 40 digits x 4 lines LCD display
- Power supply: DC 12V/1.5A. Power adapter
- Main unit: Dimensions: 184 x 160 x 78 (mm); Weight: 0.8kg
- Packaging: Dimensions: 310 x 250 x 145 (mm); Weight: 1.65kg
- Operating temperature: 0-50°C. Humidity: 20%-80%
€2,700.00*

Product Nr.: SF600
The SF600 is a high-speed ISP programmer for updating the on-board soldered SPI flash.
...show more
Hardware Features
- USB High Speed and high SPI performance, allows programming up to 2Gb SPI Flash.
- In-circuit programming: programming SPI Flash on the board
- Off-line programming: programming SPI Flash in the socket
- Start button function: Batch operation possible in USB mode
- ISP port supports 2 CS pins for programming two Serial Flash memories
- Signal conflict protection
- Multi-programming capability via USB
- Supports 1.8V low voltage IC
- Supports Windows 2003 and above
- Supports both 32 and 64 bit operating systemsSoftware Features
- PC based SF600 programming software with different modes:
- Engineering Mode features advanced developer and repair functions
- Production mode for simultaneous control of multiple SF600 Plus programmers
- Command line for controlling the SF600 through user-defined software
- Supports Windows 2003 (32 bit and 64 bit) and higher
Applications
- Updating of the serial flash soldered to the board with or without power supply in standalone or PC GUI mode
- Prototype or low volume production
- Control application, controller reset and MOSFET isolation status
- Update of internal flash (Ezport MCF5223, MCF5221, MCF5213) or external SPI flash (SBF interface MCF5445, MCF5227) of Freescale MCU
Product is discontinued

Product Nr.: SFDK01-G3
The SPI Flash Development Kit offers engineers a complete solution for the development of firmware based on SPI flash memories.
€940.00*

Product Nr.: SFDK05
This kit combines all the accessories of the EM100Pro-G3 and the SF600Plus-G2 and offers the user greater price benefits than buying them separately.
€990.00*