EEPROM Socket Programmer

Filter
–

Product Nr.: NuProg-E2
Der NuProg-E2 unterstützt UFS, eMMC, MCU, CPLD, FPGA, SPI NOR, SPI NAND, Parallel NOR, Parallel NAND und EEPROM
...show more
Hardware Features
- Built-in high speed processor for high programming speed.
- Supports UFS/UMCP and eMMC/eMCP programming.
- UFS part (v2.0/v2.1/v3.0/v3.1)
- Supports setting of descriptors, attributes and flags
- LUN configuration and preset support
- eMMC part
- Supports User Area, Boot1/2 partition and Extend CSD
- Supports RPMB, GPP1~4, and Enhanced mode
- Supports USB 2.0 and USB 3.0 (with power adapter)
- Supports various storage ICs
- UFS, eMMC, MCU, SPI NOR, SPI NAND, Parallel NOR, Parallel NAND, EEPROM, CPLD, FPGA
- Supports all IC packages
- CSP, BGA, QFN, QFP, SOP, TSOP, SSOP, PLCC, DIP, etc.
- Supports various file formats:
- Binary (bin/rom), Intel Hex (h16/h20/hex), Motorola S19(mhx/mot/s19/srec) and specific to MCU IC.
- Regular software update
- Programming project and socket are compatible with NuProgPlus.
- Socket adapters for NuProg-E2 and NuProg-E are not compatible.
- Windows 7/8/8.1/10 support
€995.00*

Product Nr.: SF600Plus-G2
The Dediprog SF600Plus-G2 is a high-speed serial NOR/NAND flash programmer with in-circuit programming.
...show more
Hardware Features
- High-speed USB and high SPI performance; the USB and standalone mode support any volume of SPI flash on the market.
- Supports 1.2V low voltage IC.
- Start button function: can batch when connected to the software.
- Protection against signal conflict.
- Multi-programmer capability via USB.
- Programmer index indicators on the programmer.
- Supports 2 CS pins.
- Stand-alone mode: support start button programming and control port to remove control programming.
- Supports WIN8 and above.
- Supports both 32bit and 64bit OS.
- Supports Single/Dual Multiple Dies.
- Supports Single/Dual/Quad/Octal. IO.
- Can be upgraded to SF600Plus-G2U.
Software Features
- PC based SF600-G2 programming software with different modes:
- Engineering Mode features advanced developer and repair functions
- Production mode for simultaneous control of multiple SF600-G2 programmers
- Command line for control of the SF600-G2 by user-defined software
- Supports Windows 2003 (32 bit and 64 bit) and higher
Applications
- Updating of the serial flash soldered to the board with or without power supply in standalone or PC GUI mode
- Prototype or low volume production, in-system or socket programming
- Control application, controller reset and MOSFET isolation status
- Update of internal flash (Ezport MCF5223, MCF5221, MCF5213) or external SPI flash (SBF interface MCF5445, MCF5227) of Freescale MCU
€380.00*
20.04 %

Product Nr.: SuperPro 610P
SuperPro 610P is a powerful and affordable 48-pin USB2.0 interface programmer that comes with free software updates.
...show more
Functions
- The universal 48-pin driver supports today's most complex devices
- Programs eMMC devices up to 64GB
- IC manufacturer approved programming algorithms
- Beginner programmer, perfect for developers and hobbyists alike
- Compatible with Windows™ 7/8/10, 32 and 64 bit
Advanced Features
- The universal 48-pin driver supports today's most complex devices
- Improved programming processor for high-speed programming
- Programs devices with a Vcc as low as 1.2V
- In-system programming () capability
- Programming / and Reminders
- Only IC manufacturer approved programming algorithms are used for high reliability
- Overcurrent and overvoltage protection for chip and programming hardware safety
- Compatible with Windows XP / Vista / 7 / 8 / 10 (32/64 bit)
- Vcc verification (at +5% ~ -5% and +10% ~ -10%) improves programming reliability
€399.00* €499.00*

Product Nr.: SuperPro-6100N
SuperPro 6100N is a low cost, reliable and fast general purpose chip programmer.
...show more
Features
- Built-in 144-pin driver
- Over 103,000 supported devices from nearly 400 IC manufacturers
- Works in PC-hosted and standalone mode
- Supports EEPROM, MCU, NOR Flash, FPGA, CPLD, SPLD, BPROM, NVRAM, EPLD
- Does not support NANDs or eMMCs
- Ultra-fast 144-pin standalone universal programmer with USB interface
- Ideal for prototyping, low volume manufacturing, master chip duplication and chip testing
Advanced Features
- Operate multiple units to build a simultaneous multi-programming system. 1-15 pieces for flexible series production.
- Supports devices with Vcc from 1.2V - 5V.
- Supports files up to 256GB
- Overcurrent and overvoltage protection for chip and programming hardware safety
- Only IC manufacturer approved programming algorithms are used for high reliability.
- Vcc verification (at +5% ~ 5% and +10% ~ 10%) improves programming reliability.
€1,099.00*

Product Nr.: SuperPro 7500N
The Xeltek SuperPro 7500N is a universal standalone programmer that can also be connected to a PC via USB or LAN.
...show more
Functions
- Algorithms designed to program up to 4 chips simultaneously
- Supports most device memories on the market
- Programs eMMC devices up to 64GB
- Supports most packet types including WLCSP
- Works in PC hosted, standalone and LAN modes
- Custom development of device algorithms available
- 144-pin universal driver
- For standard NOR/NAND FLASH devices and serial EEPROM/FLASH
- Four chips can be programmed simultaneously (depending on device type and package).
- Over 59,000 devices are supported in the SuperPro 7500 library. Adapters do not require DIP-lock sockets for transmission, resulting in more reliable connections.
- Powerful NAND FLASH platform library and exclusive solution for special cases. Supports dozens of popular NAND FLASH platforms. Quick customization available for specific needs.
- Built with 144 universal pin driver. Universal adapters are available for different packages.
- The ninth generation of pin driver technology delivers cleaner signals, a wider voltage range, a more accurate and higher clock frequency, and supports devices with Vcc from 1.2V to 5V.
- Chip safety mechanism with built-in self-correcting voltage circuitry to ensure voltage is within a preset range.
- Overcurrent and overvoltage protection for chip and programming hardware.
- Powerful yet easy-to-use software features streamline operations, improve efficiency and reduce user error during the programming process.
- Fast free technical and new device support
€1,800.00*
53.46 %

Product Nr.: K110
K110 is an engineering IC programmer that supports the majority Flash ICs on the market.
...show more
Features
- Built-in high speed processor for high programming speed.
- Support serial bus memory IC and package type.
- including SPI NOR Flash, SPI NAND Flash, EEPROM, SOP, WSON, USON and BGA.
- Support serial interface protocol including SPI, I²C and uWire.
- Supports a variety of file formats, including binary, Intel Hex, Motorola and ROM, etc.
- Provides a command line for software development.
- Supports stand-alone mode for IC programming without PC.
- ATE port with ISP adapter, provides Busy/Pass/Error and Start pins for remote control.
- Supports 1.2V low voltage IC
- Simultaneous support of multiple programmers for parallel IC programming.
€363.00* €780.00*

Product Nr.: StarProg-U
The Dediprog StarProg-U supports a variety of IC on the market, like EEPROM, SPI NOR/NAND FLASH, Parallel Flash, eMMC, MCU, etc.
...show more
Hardware Features
- Built-in high speed processor, for high programming speed.
- Supports EEPROM, SPI NOR/NAND Flash, Parallel NOR/NAND Flash, microcontroller (MCU), eMMC/eMCP, CPLD, FPGA, etc.
- Supports DIP, SOP, SSOP, TSOP, PLCC, QFN, LQFP, BGA package, etc.
- Regular device firmware update.
- Supports a variety of file formats such as binary, Intel Hex, Motorola, ROM, etc.
- Supports 1.8V low voltage ICs.
- Supports the use of third-party software to control the programmer via Windows command line.
- Powered by USB port, external power supply is not required.
- Unlimited number of StarProg-U programmers can be operated from one PC.
Produkt abgekündigt