TySOM Prototyping Boards

Recently, FPGA vendors have released SoC FPGAs that integrate ARM®-based microprocessors with their respective powerful FPGA technology into a single chip to enable more robust integration of embedded designs. Developers creating a complex embedded design only need a single integrated IC with microprocessor, DSP and FPGA to optimize system performance, flexibility and scalability. SoC FPGAs like Xilinx® Zynq™ contain the FPGA technology of the ARM Cortex ™ -A9 and Xilinx 7000 series with different capacity of logic cells, BRAM, DSP slices and I/O pins.

With such powerful devices, designers can create even more complex embedded systems. But to do that, they need powerful industry-proven development tools and prototyping platforms. eVisionSystems meets this demand with TySOM - the new series of development and prototyping boards with Xilinx Zynq devices and a complete set of peripherals and interfaces.

There is no doubt that hardware alone is not enough for the initial success of a complex embedded system. Choosing the right hardware design and verification tools for the FPGA simulation and software development environment for processors and microcontrollers is just as important as choosing a hardware platform.

TySOM board series

TySOM is a family of embedded application development boards available across all programmable Xilinx® Zynq™ modules have FPGA with ARM® Combine Cortex processor. Thanks to the large number of peripherals supplied, these cards are suitable for various embedded applications such as automotive, IoT, industrial automation or embedded HPC.

... Show more ... Show less

FMC-ADAS Automotive Daughter Card

Product Nr.: FMC-ADAS

The FMC ADAS daughter board was developed to enable prototyping and evaluation of designs for automotive with TySOM boards.

Components & Interfaces

5x FPD-Link III deserializers (DS90UB914Q-Q1) terminated with HSD camera connectors
Support URM37 V4 module with RS-232 transceiver (MAX3218) and 12-bit ADC (AD7998) for analog signal
LIDAR-Lite V2 module interface with 5V voltage levels
Buzzer
2x LVDS clock oscillators: 100MHz, 200MHz
I2C interface with EEPROM for FMC configuration data
12x status LEDs

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
Peripherals ports
- 5x HSD camera connectors
- Connection for URM37 V4 ultrasonic sensor
- Standard gold pin 1x9, 2.54mm pitch
- Connector for PulsedLight LIDAR-Lite_V2 with standard gold pin 1x6, 2.54mm spacing, 5V level shifter
- I2C connector with standard gold pin 2x5, 2.54mm spacing

Price on request

FMC-INDUSTRIAL Industrial Communication Card

Product Nr.: FMC-INDUSTRIAL

The FMC-INDUSTRIAL board was developed to enable prototyping and evaluation of industrial applications.

Components & Interfaces

Isolated full-duplex RS485 / 422 / Profibus up to 20 Mbit/s (LTM2881-3)
Isolated half-duplex RS485 / 422 / Profibus up to 40 Mbit/s (ISO1176T)
- Meets or exceeds the requirements of EN 50170 and TIA / EIA-485-A
Isolated dual RS232 up to 1Mbps (LTM2882-3)
Isolated CAN up to 4 Mbit/s (LTM2889-3)
Dual Channel Isolated Gate Driver (UCC21521ADW)
USB 3.0 Transceiver (TUSB1310A)
Digilent Pmod™ header with selectable I/O voltage 3.3V or 5V.

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
4x RJ45 for RS485, RS232 & CAN
USB 3.0 Type A connector
Terminal blocks 3.5mm pitch for RS485, RS232, CAN and gate driver interfaces
Digilent Pmod™ header, gold pin (2x6 2.54mm spacing)

Memory

64 kB EEPROM (to meet ANSI/VITA 57.1 FMC standard)

Clocking

2x oscillators (100MHz, 200MHz)

Price on request

FMC-INTF Interface Daughter Card

Product Nr.: FMC-INTF

The FMC INTF daughter card offers a good selection of commonly used peripherals such as PCIe, fiber optic QSFP+, Gigabit Ethernet, USB and more.

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
GPIO connector (20 I/O)
- 2x20 gold pin standard connectors with 2.54mm spacing
External I2C connector

Memory

4GB NAND Flash
2x 32Mb SPI Flash
Micro SD card socket
64 kB EEPROM (to meet ANSI / VITA 57.1 FMC standard)

Components & Interfaces

PCIe x4 endpoint, MOLEX 75586-0007 cable connector and lead frame
QSFP+ 4 lane MOLEX connector 75586-0010 and shield
Gigabit Ethernet RJ45 connector and Marvell PHY 88E1116R with RGMII
USB 2.0 with general purpose UART / FIFO device PHY FTDI FT2232H
UART / USB Bridge Silicon Labs CP2103
8x user LEDs, 5x status LEDs
8x user DIP switches

clock

3x oscillators 100MHz, 200MHz, 156.25MHz (reference for QSFP+)

Price on request

FMC-IOT Internet-of-Things Daughter Card

Product Nr.: FMC-IOT

The FMC-IOT Daughter Board provides peripherals and interfaces used in embedded designs that are key for IoT applications.

Components & Interfaces

Wireless/ RF
Wi-Fi IEEE 802.11a, 802.11b, 802.11g and 802.11n
Bluetooth interface (Bluetooth 4.1 compliance) with BLE
IEEE 802.15.4 standard
- ZigBee,
- 6LoWPAN,
- RF4CE,
- SP100,
- WirelessHART
Sub-GHz interfaces
Sigfox,
WMBus,
SUN interfaces according to 802.15.4g
Wired
Gigabit Ethernet (DP83867E PHY)
RS-485 / Profibus interface
3 in one Mini PCI Express / USB 2.0 / Micro SIM card socket
- USB 2.0 transceivers
- Micro SIM card socket
SATA host interface

Memory

Micro SD card socket
64 kB EEPROM (to meet ANSI / VITA 57.1 FMC standard)

Clocking

2x oscillators 100MHz, 200MHz
1x clock for SATA (150 MHz)

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
2x6 Digilent Pmod™ Compatible Header
External I2C connector

Price on request

FMC-NET Networking Daughter Card

Product Nr.: FMC-NET

The FMC-NET card was developed to enable prototyping and evaluation of various network designs.

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
Quad RJ45 Ethernet port
QSFP + MOLEX connector 75586-0010 and shield
SATA standard connector, MOLEX 67800-5005
SMA connectors for connecting antennas for wireless interfaces
JTAG connector for Ethernet PHYs

Components & Interfaces

4x Ethernet PHY 10/100/1000 with IEEE 1588 SOF (DP83867CR) with RGMII support - industrial quality
WiFi Dual Band and Bluetooth WiLink 8 Module (WL1837MOD) - Industrial Grade
1x QSFP + 4 lanes up to 40Gb/s
4x SATA device connectors

clock

2x oscillators (100MHz, 150MHz)
2x oscillators (156.25MHz, 150MHz) for QSFP+ and SATA interfaces

Memory

64 kB EEPROM (to meet ANSI/VITA 57.1 FMC standard)

Price on request

FMC-NVMe High-Bandwidth Memory Card

Product Nr.: FMC-NVMe

The FMC NVMe expansion daughter card provides four NVMe interfaces.

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
GPIO connector (20 I/O)
- 2x20 gold pin standard connectors with 2.54mm spacing
External I2C connector

Memory

4GB NAND Flash
2x 32Mb SPI Flash
Micro SD card socket
64 kB EEPROM (to meet ANSI / VITA 57.1 FMC standard)

Components & interfaces

PCIe x4 endpoint, MOLEX 75586-0007 cable connector and lead frame
QSFP+ 4 lane MOLEX connector 75586-0010 and shield
Gigabit Ethernet RJ45 connector and Marvell PHY 88E1116R with RGMII
USB 2.0 with general purpose UART / FIFO device PHY FTDI FT2232H
UART / USB Bridge Silicon Labs CP2103
8x user LEDs, 5x status LEDs
8x user DIP switches

Clock

3x oscillators 100MHz, 200MHz, 156.25MHz (reference for QSFP+)

Price on request

FMC-PCIe High-Bandwidth Serial Bus Card

Product Nr.: FMC-PCIe

The FMC PCIe daughter card can be used as a PCIe root complex.

Components & Interfaces

FMC HPC standard connector according to VITA 57.1-2010
PCIe interface x4 or x8 (connector x16)
PCIe interface x4 (connector x16)

Miscellaneous

2x oscillators (100MHz, 200MHz)
100MHz reference clocks for PCIe interfaces

Memory

64 kb EEPROM for FMC standard I2C bus

Price on request

FMC-QSFP High Speed Links Daughter Card

Product Nr.: FMC-QSFP

The FMC QSFP card provides QSFP + and SFP + expansion of FPGA prototyping cards with standard FMC connectors.

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC HPC standard
2x QSFP + 28 connector and shield
1x SFP + Amphenol UE76-A20-3000T and shield

Components & Interfaces

2x 100Gb Ethernet - QSFP28 interface connector
1x 10 Gb Ethernet - SFP + interface connector

Memory

64 kB EEPROM (to meet ANSI/VITA 57.1 FMC standard)

Clocking

2x user clock (125MHz and 156.25MHz connected to DP bank)
1x user clock (125MHz connected to CLK bank)

Price on request

FMC-VISION Multimedia Daughter Card

Product Nr.: FMC-VISION

The FMC VISION card provides a range of multimedia interfaces for display panels, monitors and cameras, which are popular in various designs such as embedded vision and the like.

Components & Interfaces

HDMI 1.4 interfaces
- HDMI IN with power-saving 165 MHz HDMI receiver ADV7611
- HDMI OUT with high power 165MHz transmitter ADV7513
DisplayPort Interfaces
- DisplayPort IN 4x channels with Linear Redriver SN65DP141
- Display Port OUT 4x channels with Linear Redriver SN65DP141
MIPI Interfaces
- MIPI CSI 2x D-Lanes with D-PHY FPGA LVDS Bridge MC20001
- MIPI DSI 2x D-Lanes with FPGA LVDS to D-PHY Bridge MC20002
USB3.0 / PCIe Host Controller to PCIe Bridge
- Based on Texas Instruments TUSB7320RKMR xHCI Host Controller
- PCIe x1 Gen2 interface to host system
- 2x USB 3.0 downstream ports
Audio codec
- Stereo audio codec SGTL5000XNAA3

Memory

64 kB EEPROM (to meet ANSI / VITA 57.1 FMC standard)

clock

2x oscillators 100MHz, 200MHz
1x clock for SATA (150 MHz)

Connectivity

Main board connector:
- FPGA mezzanine card connector according to ANSI / VITA 57.1 FMC standard
HDMI sockets
DisplayPort standard jacks
MIPI CSI / DSI - FPC connectors
Dual USB3.0 standard A socket
External I2C connector
Analog Audio Line IN and Line OUT Connectors

Price on request

TySOM-1 Prototyping Board

Product Nr.: TySOM-1

The TySOM-1 with Xilinx Zynq-7000 All Programmable FPGA is suitable for a wide range of embedded designs.

Interfaces

Gigabit Ethernet PHY with RGMII interface (88E1116R) and RJ45 connector
2x USB 2.0 ports with Hub controller (USB2514B) and Transceiver (TUSB1210)
- PCI Express / USB 3.0 subsystem - configurable one of:
- Mini PCI Express
2x USB 3.0 xHCI Host Controller (TUSB7320) bridge to PCIe
2x UART ports for Zynq PS (1.8V & 3.3V levels with TXB0108 level translator)
2x JTAG Headers
- 10-pin ARM JTAG for Zynq PS
- Xilinx JTAG Connector for Zynq PL
Digilent PMOD Compatible Header

Memory

512 MB RAM - DDR3
Micro-SD support up to 32GB
128Mb SPI Flash Memory
64 Kb EEPROM

Chipset / SoC

Xilinx Zynq-7000 XC7Z030
Dual ARM Cortex-A9 MPCore
- XADC - 12-bit, 1MSPS Analog to Digital converter
- FPGA: Kintex-7 architecture
- 125K Logic Cells, 157K Flip-Flops, 9.3Mb RAM, 400 DSP

Others

8x User Dip Switches
8x User LEDs
Reset Pushbuttons for PL & PS
RTC Module (Real Time Clock)
Accelerometer
Temperature Sensor
XADC Connector
High Speed Serial IO MMCX Connectors (1x GTX line)

Multimedia

HDMI 1.4 Out - 225 MHz High Performance Transmitter (ADV7511)
LCD & touch panel connectors
MIPI CSI - CMOS Camera Connector
Audio Codec (SGTL5000) with speaker/line-in mini-jack connector and I2S interface

Price on request

TySOM-1A Embedded Prototyping Board

Product Nr.: TySOM-1A

The configuration of the TySOM-1A board allows booting an embedded Linux operating system.

Chipset / SoC

Xilinx Zynq-7000 XC7Z010
Dual ARM Cortex-A9 MP Core
XADC - 12-bit, dual-core, 1MSPS analog-to-digital converter
FPGA: Artix 7 architecture
- 28K logic cells, 35K flip-flops, 2.1MB RAM, 80 DSP

Interfaces

Gigabit Ethernet PHY with RGMII Interface (88E1116R)
1x USB 2.0 OTG
1x USB to UART connector
1x JTAG header Xilinx JTAG connector for Zynq PL
2x Digilent PMOD compatible header

Memory

512MB RAM - DDR3
Micro SD support up to 32GB
128MB SPI flash memory
64Kb EEPROM

Others

2x user LEDs
Pushbuttons for PL & Reset PS
Accelerometer
XADC connector

Multimedia

HDMI 1.4 IN
HDMI 1.4 OUT

Dimensions

30mm x 75mm

Price on request

TySOM-2 Prototyping Board

Product Nr.: TySOM-2

TySOM-2 is a compact prototyping board that comes with the XC7Z100 chip - the largest capacity IC among the Zynq 7000 family.

Chipset / SoC

Xilinx Zynq-7000 XC7Z100 (FFG900)
Dual Core ARM Cortex-A9 MPCore
2x XADC - 12-bit analog-to-digital converter with 1 MSPS
FPGA: Kintex-7 architecture
- XC7Z100: 444K logic cells, 554K flip-flops, 26.5MB BRAM, 2020 DSP slices

Interfaces

Gigabit Ethernet PHY with RGMII interface (88E1116R) and RJ45 connector
4x USB 2.0 ports with hub controller (USB2514B) and transceiver (TUSB1210)
UART to USB Bridge (CP2103) with Mini USB B connector
Xilinx JTAG Connector for Zynq PL
6x GPIO - Gold pin 2x5 2.54 pitch connector

Others

8x user dip switches
4x user LEDs
Pushbuttons for PL & Reset PS
RTC module (real time clock)
Accelerometer
Temperature sensor
XADC connectors (pair MMCX)

Memory

1GB RAM - DDR3
Micro SD support up to 32GB
128MB SPI flash memory
64Kb EEPROM

Multimedia

HDMI 1.4 Out - 225MHz high power transmitter (ADV7511)

Price on request

TySOM-2A Prototyping Board

Product Nr.: TySOM-2A

TySOM-2A is a compact prototyping card with a mid-range Zynq-7000 module (Z-7030).

Interfaces

Gigabit Ethernet PHY with RGMII interface (88E1116R) and RJ45 connector
Additional industrial grade Gigabit Ethernet PHY with RGMII interface (DP83867CR) connected to Zynq PL supporting IEEE 1588 precision clock synchronization.
4x USB 2.0 ports with hub controller (USB2514B) and transceiver (TUSB1210)
UART to USB Bridge (CP2103) with Mini USB B connector
Xilinx JTAG Connector for Zynq PL

Chipset / SoC

Xilinx Zynq-7000 XC7Z030 (FFG676)
Dual Core ARM Cortex-A9 MPCore
2x XADC - 12-bit analog-to-digital converter with 1 MSPS
FPGA: Kintex-7 architecture
- 125K logic cells, 157K flip-flops, 9.3 MB RAM, 400 DSP

Multimedia

HDMI 1.4 Out - 225MHz high power transmitter (ADV7511)

Miscellaneous

8x user dip switches
4x user LEDs
Pushbuttons for PL & Reset PS
RTC module (real time clock)
Accelerometer
Temperature sensor
XADC connectors (pair MMCX and gold pin with 7 differential inputs)

Memory

1GB RAM - DDR3
Micro SD support up to 32GB
128MB SPI flash memory
64Kb EEPROM

Price on request

TySOM-3 Embedded Prototyping Board

Product Nr.: TySOM-3

TySOM-3-ZU7 is a compact prototyping board with Zynq® UltraScale+ ™ MPSoC device that offers 64-bit processor scalability and combines real-time control with soft and hard engines for graphics, video, waveform and packet processing.

Chipset / SoC

Xilinx Zynq UltraScale + ZU7EV-FFVC1156 MPSoC
Quad-core ARM Cortex-A53 as application processing unit
Dual-core ARM Cortex-R5 as real-time processing unit
Video codec unit
- 2x XADC - 12-bit analog-to-digital converter with 1 MSPS
- FPGA: ZU7EV
- 504K logic cells, 460,800K flip-flops, 38MB RAM, 1728 DSP

External daughterboard connector type

FMC HPC standard connector VITA 57.1-2010 compliant
FMC LPC (+5 GTH) standard connector VITA 57.1-2010 compliant

Multimedia

HDMI 2.0 Out - TE connectivity 1888811-1
HDMI 2.0 IN-TE connectivity 1888811-1
DisplayPort

Interfaces

2 × Gigabit Ethernet PHY DP83867CR
Wi-Fi / Bluetooth Module (WL1837MOD)
4x USB 3.0 ports
SATA
CAN
QSFP+
Pmod port
UART to USB Bridge (CP2103) with Mini USB B connector
Xilinx JTAG Connector for Zynq PL

Memory

4GB RAM - DDR4 Programmable Logic
4 GB DDR4 SODIMM memory for the processing system
2GB NAND memory
Micro SD support up to 32GB
256MB QSPI flash memory
64Kb EEPROM

Others

4x user dip switches
6x User LEDs
Pushbuttons for PL & Reset PS
Accelerometer
Temperature Sensor
SYSMON
Current Monitor

Price on request

TySOM-3A_Embedded_Prototyping_Board_schraege_Ansicht

TySOM-3A Embedded Prototyping Board

Product Nr.: TySOM-3A

TySOM-3A-ZU19EG provides real-time control with soft and combined hard engines for SoC prototyping solutions, IP verification, graphics, video, packet processing and early software development.

Interfaces

2 × Gigabit Ethernet PHY DP83867CR
Wi-Fi / Bluetooth Module (WL1837MOD)
PCIe x1 GEN3 / 4 (Root Complex or Endpoint)
4x USB 3.0 ports
SATA
CAN
QSFP+
2x8 IOs Pmod connector
USB 2.0 OTG (Micro USB connector)
UART to USB Bridge (CP2103) with Mini USB B connector
JTAG USB module for Zynq PL

Memory

8GB DDR4 SODIMM memory for processing system and 8GB for PL
2GB NAND memory
Micro SD support
512MB QSPI flash memory
64Kb EEPROM

Multimedia

HDMI 2.0 Out
HDMI 2.0 IN
DisplayPort

Miscellaneous

4x user dip switches
5x user LEDs
Pushbuttons for PL & Reset PS
Accelerometer
Temperature Sensor
SYSMON
Current Monitor

Chipset / SoC

Xilinx Zynq UltraScale + ZU19EG-FFVB1517 MPSoC
Quad-core ARM Cortex-A53 as application processing unit with up to 1.5 GHz
Dual-core ARM Cortex-R5 as real-time processing unit
Mali-400 MP2 graphics processing unit
- 2x XADC - 12-bit analog-to-digital converter with 1 MSPS
- FPGA: ZU19EG
- 1,143K logic cells, 1,045K flip-flops, 70.6 MB RAM, 1968 DSP

Price on request

TySOM-M-MPFS250 Prototyping Board

Product Nr.: TySOM-M-MPFS250

TySOM-M-MPFS250 is designed to provide flexibility in choosing peripherals to take full advantage of the capabilities of the PolarFire MPFS250 device.

Interfaces

2x Ethernet
1x USB 2.0
USB to UART
HDMI OUTPUT
PCIe x4 Gen2 Root
CAN
PMOD connector
2x FMC connector (HPC, LPC) Vita 57.1 compliant
4x user DIP switches
4x user LEDs
Temperature and acceleration sensor
Current and voltage monitoring

Memory

16Gb FPGA DDR4 x32
16Gb MSS DDR4 x36 with ECC
64Kb EEPROM
Micro SD socket
SPI flash memory
eMMC

Chipset / SoC

Microchip PolarFire SoC MPFS250T-FCG1152
Multi-core RISC-V processor
- SiFive E51 monitor core (1 x RV64IMAC)
- SiFive U54 application cores (4 x RV64GC)

SiFive U54 application cores (4x RV64GC)

FPGA: 254K logic cells, 17.6 MB RAM

Price on request